數控鋼筋彎箍機中文版使用操作說明書

1.1.6 良好接地

為了確保控制系統正常工作、提高系統可靠性、操作者人身安全，控制系統的所有部 分均應良好接地。系統的地線應線徑不小于 4 平方毫米，且盡量縮短與入地端的距離。

直流 24V 的地端（負端）須與大地?cái)嚅_。

1.1.7 系統的防護

保持控制系統與外部環境的隔離，以避免由于灰塵、粉塵、金屬粉塵等雜物進入控制系統 內部而造成控制系統工作不正常、系統部件損壞、降低系統壽命等。

應防護好控制系統的液晶屏幕（易碎品）：使其遠離尖銳物體；避免空中的物體撞到屏幕上 ; 不能用手指在屏幕上指點、比劃、敲打；當屏幕有灰塵需要清潔時，應·用柔軟的紙巾或棉布輕 輕擦除。

1.1.8 其它事項

系統可使用 u 盤，但 u 盤不在標準配置中，需用戶自備。

系統的各種聯接電纜、電線不在標準配置中，用戶需要時應提前說明。 產品配套“使用操作說明書”提供一本。

由于不符合安全須知，而造成的系統損壞，不在保修范圍內。

1.2 控制系統的啟動與關機

控制系統是機床數控系統的核心，對系統的使用應按照系統的操作要求進行。

1.2.1 控制系統的啟動

當箍筋握彎?rùn)C(jī)系統電源開啟后，系統自動引導進入控制系統軟件的開機畫面。然后再打開驅動器的供電電源。不要頻繁打開、切斷系統電源，否則易造成控制系統或開關電源的損壞。

1.2. 2 控制系統的關機

數控鋼筋彎箍機操作完成后，需關閉控制系統時，應按先關閉驅動器的電源，然后再關閉控制系統的電源 , 避免干擾造成的電機誤動作。

1.1.6 Good grounding

In order to ensure the normal operation of the control system, improve system reliability, and ensure the personal safety of the operator, all parts of the control system should be well grounded.

The ground wire of the system should ensure that the wire diameter is not less than 4 square millimeters, and the distance to the ground terminal should be shortened as much as possible.

The ground terminal (negative terminal) of DC 24V must be disconnected from the ground.

1.1.7 System protection

Keep the control system isolated from the external environment to prevent dust, dust, metal dust and other debris from entering the control system, which may cause the control system to work abnormally, damage system components, and reduce system life.

The LCD screen (fragile) of the control system should be protected: keep it away from sharp objects; prevent objects in the air from hitting the screen; do not use your fingers to point, gesture, or tap on the screen; when the screen is dusty and needs to be cleaned, ·Use a soft paper towel or cotton cloth to wipe gently.

1.1.8 Other matters

The system can use a USB flash drive, but the USB flash drive is not in the standard configuration and needs to be prepared by the user.

The various connecting cables and wires of the system are not in the standard configuration, and the user should explain in advance when needed. Only one copy of the "Operation Manual" is provided for free.

System damage caused by non-compliance with safety instructions is not covered by the warranty.

1.2 Startup and shutdown of the control system

The control system is the core of the machine tool numerical control system, and the use of the system should be carried out in accordance with the operating requirements of the system.

1.2.1 Start of control system

When the system power is turned on, the system automatically boots into the startup screen of the control system software. Then turn on the power supply of the drive.

Do not frequently open or cut off the system power supply, otherwise the control system or switching power supply may be damaged.

1. 2. 2 Shutdown of control system

After the operation is completed, when you need to turn off the control system, you should turn off the power of the drive first, and then turn off the power of the control system to avoid motor malfunction caused by interference.